Fan: Difference between revisions
No edit summary |
No edit summary |
||
| Line 74: | Line 74: | ||
The following fans were used with prototype consoles. | The following fans were used with prototype consoles. | ||
=== | === Cooler Master === | ||
Used with Xbox 360 internal prototypes, this fan was used on open-air internal debug consoles. To see more, see heatsinks. | Used with Xbox 360 internal prototypes, this fan was used on open-air internal debug consoles. To see more, see heatsinks. | ||
* Model: A9020-30CB-4AP-C1 | * Model: A9020-30CB-4AP-C1 | ||
| Line 81: | Line 81: | ||
File:X360P Proto SLT Fan (2).jpg | File:X360P Proto SLT Fan (2).jpg | ||
</gallery> | </gallery> | ||
=== Cooler Master === | |||
=== | |||
Used with early Xbox 360 S trinity prototypes, this fan was slimmer than final fans and was mounted to a taller heatsink. To see more, see heatsinks. | Used with early Xbox 360 S trinity prototypes, this fan was slimmer than final fans and was mounted to a taller heatsink. To see more, see heatsinks. | ||
* Model: A9020-30CB-4AP-C1 | * Model: A9020-30CB-4AP-C1 | ||
| Line 93: | Line 89: | ||
File:X360S CM (3).jpg | File:X360S CM (3).jpg | ||
File:X360S CM (4).jpg | File:X360S CM (4).jpg | ||
</gallery>{{Console Components}} | </gallery> | ||
=== Protechnic Magic === | |||
Used with early Xbox 360 xenon prototypes, this fan was used on the GPU and CPU heatsinks of internal System-Level Tester (SLT) consoles that featured a hot-swap socket. To see more, see heatsinks. | |||
* Model: MGT7012ZC-A15 | |||
{{Console Components}} | |||
[[Category:Console Components]] | [[Category:Console Components]] | ||
Revision as of 20:20, 9 April 2024
The Xbox 360 has used multiple different type of fans for cooling the processors. The fans are controlled by the SMC using the Thermal Algorithm.
Dual Fan
Dual fan assemblies were used in the Original Xbox 360 and pulled air through the heatsink through a shroud. There are 3 different fans used from different vendors. For Xenon motherboards, the connector is a 4-pin connector, with a power and ground for each fan. All other models use a 3-pin fan connector with a common ground and power for each fan.
Delta
- Model: AUB0712HH
Top
Bottom
Nidec
- Model: E35427-55MIC13
Top
Bottom
Sunon
- Model: KDE1207PTVX-A
Top
Bottom
Single Fan
The Xbox 360 S and Xbox 360 E used a single fan mounted directly to the heatsink in a more traditional configuration. There are 4 different fans used from different vendors. They use a 4-pin PWM connector.
Cooler Master
- Model: FA09025H12LPA
Top
Bottom
Delta (Type 1)
- Model: AUB0912HH
Top
Bottom
Delta (Type 2)
- Model: AUB0912HH
Top
Bottom
Foxconn
- Model: AUB0912HH
Top
Bottom
Prototypes
The following fans were used with prototype consoles.
Cooler Master
Used with Xbox 360 internal prototypes, this fan was used on open-air internal debug consoles. To see more, see heatsinks.
- Model: A9020-30CB-4AP-C1
- X360P Proto SLT Fan (1).jpg
- X360P Proto SLT Fan (2).jpg
Cooler Master
Used with early Xbox 360 S trinity prototypes, this fan was slimmer than final fans and was mounted to a taller heatsink. To see more, see heatsinks.
- Model: A9020-30CB-4AP-C1
- X360S CM (10).jpg
- X360S CM (11).jpg
- X360S CM (3).jpg
- X360S CM (4).jpg
Protechnic Magic
Used with early Xbox 360 xenon prototypes, this fan was used on the GPU and CPU heatsinks of internal System-Level Tester (SLT) consoles that featured a hot-swap socket. To see more, see heatsinks.
- Model: MGT7012ZC-A15