Heatsink: Difference between revisions
m (→Prototypes) |
|||
| Line 62: | Line 62: | ||
The following heatsinks were used on different Xbox 360 console variations. | The following heatsinks were used on different Xbox 360 console variations. | ||
=== | === Cooler Master Fan === | ||
====Workbench Cooler==== | |||
Used internally in a variety of applications. This heatsink featured a copper slug and a downward-facing Cooler Master fan. The thermal interface material (TIM) that was used on this was sized for up to a Shiva CPU.<gallery> | Used internally in a variety of applications. This heatsink featured a copper slug and a downward-facing Cooler Master fan. The thermal interface material (TIM) that was used on this was sized for up to a Shiva CPU.<gallery> | ||
File:X360 CM Int HS (1).jpg | File:X360 CM Int HS (1).jpg | ||
| Line 72: | Line 73: | ||
</gallery> | </gallery> | ||
=== | ====X820716-002, REV G==== | ||
Used on early Trinity prototypes, this heatsink is thicker than the final heatsink and does not feature a copper slug. This was used in correlation with a different fan shroud as well with F92 markings. This was seen publicly in a leak before the trinity motherboard was released. | Used on early Trinity prototypes, this heatsink is thicker than the final heatsink and does not feature a copper slug. This was used in correlation with a different fan shroud as well with F92 markings. This was seen publicly in a leak before the trinity motherboard was released. | ||
<gallery> | <gallery> | ||
File:X360S CM (2).jpg | File:X360S CM (2).jpg | ||
| Line 89: | Line 86: | ||
File:500x xbox-motherboard.jpg | File:500x xbox-motherboard.jpg | ||
</gallery> | </gallery> | ||
=== Xbox 360 Solid-Copper Base Heat Pipe Heatsink === | |||
Used on early xenon prototypes, this heatsink featured solid copper base and was used on both Shiva and DD1 CPUs. When used with a Shiva CPU, the standoffs were lengthened to account for the taller IHS. Due to this, the heatsink fins were shorter than that of the final heatsink. | |||
{{Console Components}} | {{Console Components}} | ||
[[Category:Console Components]] | [[Category:Console Components]] | ||
Revision as of 20:44, 9 April 2024
The Xbox 360 has used multiple different type of heatsinks for cooling the processors.
Xbox 360 (Original)
The Original Xbox 360 used 2 heatsinks: one for the CPU, and one for the GPU. There were also 2 different versions of each heatsink.
Heatpipe CPU
Used on the Xenon, Zephyr, and Elpis motherboards. It was also used on very early versions of the Falcon motherboard. Later revisions found on late 2006 and newer boards had less of a cutout near the rounded heat pipe on the side.
Aluminum CPU
Used on the Falcon, Jasper, and Tonasket motherboards.
Low Profile GPU
Used on early/mid Xenon motherboards, Zephyr_A motherboards, and returned on the Tonasket motherboard.
Extended GPU
Used on late Xenon, Zephyr_B/C, Elpis, Falcon, and Jasper motherboards.
Xbox 360 S and Xbox 360 E
The Xbox 360 S and Xbox 360 E use a single heatsink for the CGPU. There were 2 versions of the heatsink. Both versions have a fan mounted on them.
Heatsink with a fan mounted on top
Bottom of the heatsink
Tall Slug
Used on the Trinity motherboard. This heatsink was only used for a brief time.
Short Slug
Used on the Trinity, Corona, Waitsburg, and Stingray motherboards. It was also used on Winchester with slightly shortened pegs on the bottom, as Winchester removed the integrated heat spreader.
Prototypes
The following heatsinks were used on different Xbox 360 console variations.
Cooler Master Fan
Workbench Cooler
Used internally in a variety of applications. This heatsink featured a copper slug and a downward-facing Cooler Master fan. The thermal interface material (TIM) that was used on this was sized for up to a Shiva CPU.
- X360 CM Int HS (1).jpg
- X360 CM Int HS (2).jpg
- X360 CM Int HS (3).jpg
- X360 CM Int HS (4).jpg
- X360 CM Int HS (5).jpg
- Xbox-360-xavbox.jpg
X820716-002, REV G
Used on early Trinity prototypes, this heatsink is thicker than the final heatsink and does not feature a copper slug. This was used in correlation with a different fan shroud as well with F92 markings. This was seen publicly in a leak before the trinity motherboard was released.
- X360S CM (2).jpg
- X360S CM (5).jpg
- X360S CM (6).jpg
- X360S CM (7).jpg
- X360S CM (9).jpg
- X360S CM (1).jpg
- X360S CM (8).jpg
- 500x xbox-motherboard.jpg
Xbox 360 Solid-Copper Base Heat Pipe Heatsink
Used on early xenon prototypes, this heatsink featured solid copper base and was used on both Shiva and DD1 CPUs. When used with a Shiva CPU, the standoffs were lengthened to account for the taller IHS. Due to this, the heatsink fins were shorter than that of the final heatsink.