Falcon: Difference between revisions

From XenonLibrary
Jump to navigation Jump to search
No edit summary
No edit summary
(2 intermediate revisions by the same user not shown)
Line 4: Line 4:
| introduced  = Late 2007
| introduced  = Late 2007
| partnumber  = X812320
| partnumber  = X812320
| type        = Motherboard
| usedin      = [[Xbox 360 (Original)]]
| usedin      = [[Xbox 360 (Original)]]
| cputype      = [[Loki]]
| cputype      = [[Loki]]
Line 57: Line 56:
* Removal of the HDMI port
* Removal of the HDMI port
* Custom A/V port to fit the HDMI board layout while being able to fit into the Xenon casing
* Custom A/V port to fit the HDMI board layout while being able to fit into the Xenon casing
* All Opus boards use revised versions of the [[Rhea]] GPU with higher Tg underfill
* All Opus boards use 4x128MB [[Qimonda RAM#HYB18H1G321AF-14|Qimonda HYB18H1G321AF-14]] RAM
* All Opus boards use 4x128MB [[Qimonda RAM#HYB18H1G321AF-14|Qimonda HYB18H1G321AF-14]] RAM


{{Console Components}}
{{Console Components}}
[[Category:Motherboards]]
[[Category:Motherboards]]

Revision as of 19:16, 3 April 2023

Falcon
X812320-003.jpg
Part NumberX812320
IntroducedLate 2007
Used InXbox 360 (Original)
CPU TypeLoki
GPU TypeRhea
CPU Process65nm
GPU Process80nm
eDRAM Process80nm
Nand Size16MB (Retail)
64MB (Dev)
Video OutputsA/V and HDMI
Wattage175W
12V Amperage14.2A
PredecessorZephyr_C
SuccessorJasper

Falcon is the successor to Zephyr_C and is used in the Original Xbox 360 series.

Notable Differences

  • The 90nm Waternoose CPU has been replaced with the 65nm Loki CPU
  • When the revised GPUs rolled out, around March 2008, all board started using Qimonda HYB18H1G321AF-14 RAM in a 4x128MB config
  • Qimonda HYB18H512322AF-13 RAM has been replaced with Qimonda HYB18H512321BF-14
  • When the revised GPUs rolled out, Hynix HY5RS123235BFP-14 and Qimonda HYB18H512321BF-13 RAM are no longer used
  • Around March 2008, fixed GPUs started being used
  • The CPU voltage regulation is now 2 phases, down from 3 phases, but the pads and silkscreen for the third phase still remain
  • The board layout has been modified to support the 65nm CPU
  • Other small changes were made to the board layout
  • The J7G3 Titan connector on the front of the motherboard was left on the final motherboard
  • Some later boards use solid state capacitors for the CPU and GPU output filters
  • The heatpipe CPU heatsink was replaced with the aluminum CPU heatsink, however some early boards did not have this change

Specifications

Opus

The Opus motherboard is exactly the same as the Falcon, with exception to a custom A/V port that is installed, and the removal of the HDMI port. These modifications allow the Opus to fit into the casings for a Xenon. This was used for refurbishing defective consoles until the Elpis boards started being produced. The part number is also the same as Falcon.

Notable Differences

  • Removal of the HDMI port
  • Custom A/V port to fit the HDMI board layout while being able to fit into the Xenon casing
  • All Opus boards use revised versions of the Rhea GPU with higher Tg underfill
  • All Opus boards use 4x128MB Qimonda HYB18H1G321AF-14 RAM